1. The working principle of anticorrosive impregnating tank for building mesh.

　　2、槽體為長條狀容器，內裝防腐劑;槽中設置有攪拌器。

　　2. The tank body is a long strip container with preservative in it; the tank is equipped with an agitator.

　　3、攪拌器可以在槽內左右移動，把防腐劑攪拌均勻，以保證浸漬質量的穩定。攪拌器的移動靠電機5通過鏈條6帶動。

　　3. The agitator can move left and right in the tank to mix the preservative evenly to ensure the stability of the impregnation quality. The movement of the agitator is driven by the motor 5 through the chain 6.

　　由于防腐劑是懸浮液，必須依靠攪拌機了維持槽內防腐劑的均勻，否則將影響防腐涂層效果。

　　As the preservative is a suspension, it must rely on the mixer to maintain the uniformity of the preservative in the tank, otherwise it will affect the effect of the anticorrosive coating.

　　4、建筑網片烘干機，用蒸氣作為加熱介質，蒸氣通過散熱器對箱內網片進行加熱。每箱可裝入十幾組鋼筋網片，建筑網片從入口裝入，放在傳動鏈條上，每裝入一組鋼筋網片鏈條就移動一次，經過一定時間的移動烘干，烘干完畢的網片由出口吊出。

　　4. The building mesh dryer uses steam as the heating medium, and the steam heats the mesh in the box through the radiator. Each box can be loaded with more than ten groups of steel mesh. The construction mesh is loaded from the entrance and placed on the transmission chain. Each group of steel mesh chain is moved once. After a certain time of moving and drying, the dried mesh is lifted out from the exit.

　　5、自動防腐烘干生產線是一個兩層的鋼框架。鋼筋網片用鋼釬、鋼梁、組裝框架組成一組。用吊車吊下層行走組裝網片小車，小車在下層軌道上移動，移動是用軌道旁的液壓缸帶動。

　　5. The automatic anti-corrosion drying production line is a two-layer steel frame. The steel mesh is composed of steel drill rod, steel beam and assembly frame. Hoist the trolley to the lower layer and assemble the mesh trolley. The trolley moves on the lower rail. The movement is driven by the hydraulic cylinder beside the rail.

　　當移可升降的臺架處時，臺架下降，使鋼筋浸入浸漬槽內，然后臺架上升，并振動片刻，使多余的防腐劑滴入槽中;小車?yán)^續前進，進入熱風箱內進行烘干。

　　When it is moved to the lifting platform, the platform will be lowered so that the reinforcement will be immersed in the immersion tank, then the platform will be raised and vibrated for a moment, so that the excess preservative will drop into the tank; the car will continue to move forward and enter the hot air box for drying.

　　烘干后的網片再進入第二個浸漬槽中進行第二次浸漬烘干，然后提升架升上層軌道返回，再進入烘干箱內進行二次烘干，完成防腐工作。

　　The dried mesh enters the second soaking tank for the second soaking and drying, then the lifting frame rises to the upper track and returns, then enters the drying box for the second drying, and finally completes the anti-corrosion work.

　　烘干的建筑網片由天車吊起將網片組放入模具中。這條網片防腐生產加工線，每6分鐘完成一組網片的防腐加工，產量很高。

　　The dried construction mesh is hoisted by the crown block to put the mesh group into the mold. This anti-corrosion production and processing line completes the anti-corrosion processing of one network piece every 6 minutes, with high output.